Category: PUMPX manual instruction

Installing a self-priming tank, if your SAL pump is used for vertical, upward suction, it will be possible for you to use the pump for the following applications: 1. Install where a general-purpose pump with foot valve is being used. There are many cases of problems arising with a foot valve pump because the valve…

The pump vibrates and is noisy when operating. Below are some common causes of malfunctions and solutions.If you are unable to resolve the problem, please contact us. Cause Countermeasure The bearing is damaged  Replace the bearing Too much discharge  Adjust the discharge valve to the specified water volume. The impeller is clogged with foreign matter …

Overload (overcurrent) Below are some common causes of malfunctions and solutions.If you are unable to resolve the problem, please contact us. Cause Countermeasure High rotation speed. The number of poles of the motor is different.  Check the nameplate and replace it with a genuine one High voltage  Check the power supply A 50Hz pump is…

Water comes out at first but soon stops Below are some common causes of malfunctions and solutions.If you are unable to resolve the problem, please contact us. Cause Countermeasure Insufficient priming  Prime the tank sufficiently Inhaling air  Inspect and repair the suction pipe and shaft seal. Air trapped in the suction piping  Reinstall the piping…

The pump rotates but no water comes out. The specified discharge volume is not achieved. Below are some common causes of malfunctions and solutions.If you are unable to resolve the problem, please contact us. CAUSE Countermeasure Unprimed  To bait The gate valve is closed or ajar  Open the gate valve The rotation direction is reversed …

The motor does not turn. The motor hums but does not turn. Below are some common causes of malfunctions and solutions.If you are unable to resolve the problem, please contact us. Cause Countermeasure The motor is broken  Repairing an electric motor There is a problem with the power supply  Inspect and repair Rotating parts are…

MODEL LS, LM, LL Safety Information and Introduction WARNING Do not work under heavy suspended object unless there is a positive support under it to stop Its fall in event of sling or hoist failure. Disregard of this war­ning could result in personal injury. This Quick Discharge Connector should only be serviced by a qualified…

Sprinkler System        A sprinkler system is an integrated system of piping, connected to a water supply, with listed sprinklers that automatically initiate water discharge over a fire area. Usually the sprinkler system also includes a control valve and a device for activating an alarm when the system operates.          Each sprinkler has its own individual heat…

OIL lubrication – Bearing 1,Selection of turbine oil.ISO VG46 2,Maintenance Change the oil after 300 hours for new bearings.Add oil until level is at the center of the sight glass. 3,Sight glassDimensions comply with JB/T7941.2Technical requirements comply with GB1163 Flushing for gland packing 1) If delivered liquid temperature is over than 100℃, external flushing is…

CLASSIFICATION OF TURBO PUMPS Turbo pumps are loosely grouped into the following three types.1- Centrifugal PumpPump head caused primarily by the centrifugal force of impeller rotation. This type pump is widely used for its high head capability. 2-Mixed Flow PumpHere pump head is derived partly from rotation of the impeller, partly from impeller lift. 3-Axial…

EBARA CORPORATION I- Our lives and pump Water is essential for our lives. Although we usu­ally use water without thinking, benefits that we obtain from it are immeasurable. Life with an abundance of water is our fervent hope. Pumps help us to realize this hope and therefore we cannot do without them. It is hardly…

Introduction Check the following points upon receipt of your pump:(1) Is the pump exactly what you ordered? Check the name­ plate. It is especially important that you check whether the pump is to be used with 50 Hz or 60 Hz.(2) Has any damage occurred during shipment? Are any bolts or nuts loose? (3) Have…

Installation 1. Location (1) This pump should be installed indoors (except for option pump of outdoor ＋ motor of outdoor).(2) There should be ample space around the pump, and securing a large working space for maintenance and inspection.(3) Provide an enclosure around the pump, or take some other effective measures to prevent unauthorized personnel from…